1. 漏洞描述

The Linux Kernel, the operating system core itself.

Security Fix(es):

In the Linux kernel, the following vulnerability has been resolved:

ALSA: gus: fix null pointer dereference on pointer block

The pointer block return from snd_gf1_dma_next_block could be
null, so there is a potential null pointer dereference issue.
Fix this by adding a null check before dereference.(CVE-2021-47207)

In the Linux kernel, the following vulnerability has been resolved:

mlxsw: spectrum_acl_tcam: Fix stack corruption

When tc filters are first added to a net device, the corresponding local
port gets bound to an ACL group in the device. The group contains a list
of ACLs. In turn, each ACL points to a different TCAM region where the
filters are stored. During forwarding, the ACLs are sequentially
evaluated until a match is found.

One reason to place filters in different regions is when they are added
with decreasing priorities and in an alternating order so that two
consecutive filters can never fit in the same region because of their
key usage.

In Spectrum-2 and newer ASICs the firmware started to report that the
maximum number of ACLs in a group is more than 16, but the layout of the
register that configures ACL groups (PAGT) was not updated to account
for that. It is therefore possible to hit stack corruption [1] in the
rare case where more than 16 ACLs in a group are required.

Fix by limiting the maximum ACL group size to the minimum between what
the firmware reports and the maximum ACLs that fit in the PAGT register.

Add a test case to make sure the machine does not crash when this
condition is hit.

[1]
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: mlxsw_sp_acl_tcam_group_update+0x116/0x120
[...]
dump_stack_lvl+0x36/0x50
panic+0x305/0x330
__stack_chk_fail+0x15/0x20
mlxsw_sp_acl_tcam_group_update+0x116/0x120
mlxsw_sp_acl_tcam_group_region_attach+0x69/0x110
mlxsw_sp_acl_tcam_vchunk_get+0x492/0xa20
mlxsw_sp_acl_tcam_ventry_add+0x25/0xe0
mlxsw_sp_acl_rule_add+0x47/0x240
mlxsw_sp_flower_replace+0x1a9/0x1d0
tc_setup_cb_add+0xdc/0x1c0
fl_hw_replace_filter+0x146/0x1f0
fl_change+0xc17/0x1360
tc_new_tfilter+0x472/0xb90
rtnetlink_rcv_msg+0x313/0x3b0
netlink_rcv_skb+0x58/0x100
netlink_unicast+0x244/0x390
netlink_sendmsg+0x1e4/0x440
____sys_sendmsg+0x164/0x260
___sys_sendmsg+0x9a/0xe0
__sys_sendmsg+0x7a/0xc0
do_syscall_64+0x40/0xe0
entry_SYSCALL_64_after_hwframe+0x63/0x6b(CVE-2024-26586)

In the Linux kernel, the following vulnerability has been resolved:

KVM: arm64: vgic-its: Avoid potential UAF in LPI translation cache

There is a potential UAF scenario in the case of an LPI translation
cache hit racing with an operation that invalidates the cache, such
as a DISCARD ITS command. The root of the problem is that
vgic_its_check_cache() does not elevate the refcount on the vgic_irq
before dropping the lock that serializes refcount changes.

Have vgic_its_check_cache() raise the refcount on the returned vgic_irq
and add the corresponding decrement after queueing the interrupt.(CVE-2024-26598)

In the Linux kernel, the following vulnerability has been resolved:

sched/membarrier: reduce the ability to hammer on sys_membarrier

On some systems, sys_membarrier can be very expensive, causing overall
slowdowns for everything. So put a lock on the path in order to
serialize the accesses to prevent the ability for this to be called at
too high of a frequency and saturate the machine.(CVE-2024-26602)

In the Linux kernel, the following vulnerability has been resolved:

tun: limit printing rate when illegal packet received by tun dev

vhost_worker will call tun call backs to receive packets. If too many
illegal packets arrives, tun_do_read will keep dumping packet contents.
When console is enabled, it will costs much more cpu time to dump
packet and soft lockup will be detected.

net_ratelimit mechanism can be used to limit the dumping rate.

PID: 33036 TASK: ffff949da6f20000 CPU: 23 COMMAND: "vhost-32980"
#0 [fffffe00003fce50] crash_nmi_callback at ffffffff89249253
#1 [fffffe00003fce58] nmi_handle at ffffffff89225fa3
#2 [fffffe00003fceb0] default_do_nmi at ffffffff8922642e
#3 [fffffe00003fced0] do_nmi at ffffffff8922660d
#4 [fffffe00003fcef0] end_repeat_nmi at ffffffff89c01663
[exception RIP: io_serial_in+20]
RIP: ffffffff89792594 RSP: ffffa655314979e8 RFLAGS: 00000002
RAX: ffffffff89792500 RBX: ffffffff8af428a0 RCX: 0000000000000000
RDX: 00000000000003fd RSI: 0000000000000005 RDI: ffffffff8af428a0
RBP: 0000000000002710 R8: 0000000000000004 R9: 000000000000000f
R10: 0000000000000000 R11: ffffffff8acbf64f R12: 0000000000000020
R13: ffffffff8acbf698 R14: 0000000000000058 R15: 0000000000000000
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#5 [ffffa655314979e8] io_serial_in at ffffffff89792594
#6 [ffffa655314979e8] wait_for_xmitr at ffffffff89793470
#7 [ffffa65531497a08] serial8250_console_putchar at ffffffff897934f6
#8 [ffffa65531497a20] uart_console_write at ffffffff8978b605
#9 [ffffa65531497a48] serial8250_console_write at ffffffff89796558
#10 [ffffa65531497ac8] console_unlock at ffffffff89316124
#11 [ffffa65531497b10] vprintk_emit at ffffffff89317c07
#12 [ffffa65531497b68] printk at ffffffff89318306
#13 [ffffa65531497bc8] print_hex_dump at ffffffff89650765
#14 [ffffa65531497ca8] tun_do_read at ffffffffc0b06c27 [tun]
#15 [ffffa65531497d38] tun_recvmsg at ffffffffc0b06e34 [tun]
#16 [ffffa65531497d68] handle_rx at ffffffffc0c5d682 [vhost_net]
#17 [ffffa65531497ed0] vhost_worker at ffffffffc0c644dc [vhost]
#18 [ffffa65531497f10] kthread at ffffffff892d2e72
#19 [ffffa65531497f50] ret_from_fork at ffffffff89c0022f(CVE-2024-27013)

In the Linux kernel, the following vulnerability has been resolved:

netfilter: nfnetlink_queue: acquire rcu_read_lock() in instance_destroy_rcu()

syzbot reported that nf_reinject() could be called without rcu_read_lock() :

WARNING: suspicious RCU usage
6.9.0-rc7-syzkaller-02060-g5c1672705a1a #0 Not tainted

net/netfilter/nfnetlink_queue.c:263 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 2, debug_locks = 1
2 locks held by syz-executor.4/13427:
#0: ffffffff8e334f60 (rcu_callback){....}-{0:0}, at: rcu_lock_acquire include/linux/rcupdate.h:329 [inline]
#0: ffffffff8e334f60 (rcu_callback){....}-{0:0}, at: rcu_do_batch kernel/rcu/tree.c:2190 [inline]
#0: ffffffff8e334f60 (rcu_callback){....}-{0:0}, at: rcu_core+0xa86/0x1830 kernel/rcu/tree.c:2471
#1: ffff88801ca92958 (&inst->lock){+.-.}-{2:2}, at: spin_lock_bh include/linux/spinlock.h:356 [inline]
#1: ffff88801ca92958 (&inst->lock){+.-.}-{2:2}, at: nfqnl_flush net/netfilter/nfnetlink_queue.c:405 [inline]
#1: ffff88801ca92958 (&inst->lock){+.-.}-{2:2}, at: instance_destroy_rcu+0x30/0x220 net/netfilter/nfnetlink_queue.c:172

stack backtrace:
CPU: 0 PID: 13427 Comm: syz-executor.4 Not tainted 6.9.0-rc7-syzkaller-02060-g5c1672705a1a #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/02/2024
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x241/0x360 lib/dump_stack.c:114
lockdep_rcu_suspicious+0x221/0x340 kernel/locking/lockdep.c:6712
nf_reinject net/netfilter/nfnetlink_queue.c:323 [inline]
nfqnl_reinject+0x6ec/0x1120 net/netfilter/nfnetlink_queue.c:397
nfqnl_flush net/netfilter/nfnetlink_queue.c:410 [inline]
instance_destroy_rcu+0x1ae/0x220 net/netfilter/nfnetlink_queue.c:172
rcu_do_batch kernel/rcu/tree.c:2196 [inline]
rcu_core+0xafd/0x1830 kernel/rcu/tree.c:2471
handle_softirqs+0x2d6/0x990 kernel/softirq.c:554
__do_softirq kernel/softirq.c:588 [inline]
invoke_softirq kernel/softirq.c:428 [inline]
__irq_exit_rcu+0xf4/0x1c0 kernel/softirq.c:637
irq_exit_rcu+0x9/0x30 kernel/softirq.c:649
instr_sysvec_apic_timer_interrupt arch/x86/kernel/apic/apic.c:1043 [inline]
sysvec_apic_timer_interrupt+0xa6/0xc0 arch/x86/kernel/apic/apic.c:1043
</IRQ>
<TASK>(CVE-2024-36286)

In the Linux kernel, the following vulnerability has been resolved:

net: relax socket state check at accept time.

Christoph reported the following splat:

WARNING: CPU: 1 PID: 772 at net/ipv4/af_inet.c:761 __inet_accept+0x1f4/0x4a0
Modules linked in:
CPU: 1 PID: 772 Comm: syz-executor510 Not tainted 6.9.0-rc7-g7da7119fe22b #56
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
RIP: 0010:__inet_accept+0x1f4/0x4a0 net/ipv4/af_inet.c:759
Code: 04 38 84 c0 0f 85 87 00 00 00 41 c7 04 24 03 00 00 00 48 83 c4 10 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc e8 ec b7 da fd <0f> 0b e9 7f fe ff ff e8 e0 b7 da fd 0f 0b e9 fe fe ff ff 89 d9 80
RSP: 0018:ffffc90000c2fc58 EFLAGS: 00010293
RAX: ffffffff836bdd14 RBX: 0000000000000000 RCX: ffff888104668000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: dffffc0000000000 R08: ffffffff836bdb89 R09: fffff52000185f64
R10: dffffc0000000000 R11: fffff52000185f64 R12: dffffc0000000000
R13: 1ffff92000185f98 R14: ffff88810754d880 R15: ffff8881007b7800
FS: 000000001c772880(0000) GS:ffff88811b280000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fb9fcf2e178 CR3: 00000001045d2002 CR4: 0000000000770ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
<TASK>
inet_accept+0x138/0x1d0 net/ipv4/af_inet.c:786
do_accept+0x435/0x620 net/socket.c:1929
__sys_accept4_file net/socket.c:1969 [inline]
__sys_accept4+0x9b/0x110 net/socket.c:1999
__do_sys_accept net/socket.c:2016 [inline]
__se_sys_accept net/socket.c:2013 [inline]
__x64_sys_accept+0x7d/0x90 net/socket.c:2013
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x58/0x100 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x4315f9
Code: fd ff 48 81 c4 80 00 00 00 e9 f1 fe ff ff 0f 1f 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 ab b4 fd ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffdb26d9c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002b
RAX: ffffffffffffffda RBX: 0000000000400300 RCX: 00000000004315f9
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000004
RBP: 00000000006e1018 R08: 0000000000400300 R09: 0000000000400300
R10: 0000000000400300 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000040cdf0 R14: 000000000040ce80 R15: 0000000000000055
</TASK>

The reproducer invokes shutdown() before entering the listener status.
After commit 94062790aedb ("tcp: defer shutdown(SEND_SHUTDOWN) for
TCP_SYN_RECV sockets"), the above causes the child to reach the accept
syscall in FIN_WAIT1 status.

Eric noted we can relax the existing assertion in __inet_accept()(CVE-2024-36484)

In the Linux kernel, the following vulnerability has been resolved:

tcp: Use refcount_inc_not_zero() in tcp_twsk_unique().

Anderson Nascimento reported a use-after-free splat in tcp_twsk_unique()
with nice analysis.

Since commit ec94c2696f0b ("tcp/dccp: avoid one atomic operation for
timewait hashdance"), inet_twsk_hashdance() sets TIME-WAIT socket's
sk_refcnt after putting it into ehash and releasing the bucket lock.

Thus, there is a small race window where other threads could try to
reuse the port during connect() and call sock_hold() in tcp_twsk_unique()
for the TIME-WAIT socket with zero refcnt.

If that happens, the refcnt taken by tcp_twsk_unique() is overwritten
and sock_put() will cause underflow, triggering a real use-after-free
somewhere else.

To avoid the use-after-free, we need to use refcount_inc_not_zero() in
tcp_twsk_unique() and give up on reusing the port if it returns false.

[0]:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 0 PID: 1039313 at lib/refcount.c:25 refcount_warn_saturate+0xe5/0x110
CPU: 0 PID: 1039313 Comm: trigger Not tainted 6.8.6-200.fc39.x86_64 #1
Hardware name: VMware, Inc. VMware20,1/440BX Desktop Reference Platform, BIOS VMW201.00V.21805430.B64.2305221830 05/22/2023
RIP: 0010:refcount_warn_saturate+0xe5/0x110
Code: 42 8e ff 0f 0b c3 cc cc cc cc 80 3d aa 13 ea 01 00 0f 85 5e ff ff ff 48 c7 c7 f8 8e b7 82 c6 05 96 13 ea 01 01 e8 7b 42 8e ff <0f> 0b c3 cc cc cc cc 48 c7 c7 50 8f b7 82 c6 05 7a 13 ea 01 01 e8
RSP: 0018:ffffc90006b43b60 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffff888009bb3ef0 RCX: 0000000000000027
RDX: ffff88807be218c8 RSI: 0000000000000001 RDI: ffff88807be218c0
RBP: 0000000000069d70 R08: 0000000000000000 R09: ffffc90006b439f0
R10: ffffc90006b439e8 R11: 0000000000000003 R12: ffff8880029ede84
R13: 0000000000004e20 R14: ffffffff84356dc0 R15: ffff888009bb3ef0
FS: 00007f62c10926c0(0000) GS:ffff88807be00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020ccb000 CR3: 000000004628c005 CR4: 0000000000f70ef0
PKRU: 55555554
Call Trace:
<TASK>
? refcount_warn_saturate+0xe5/0x110
? __warn+0x81/0x130
? refcount_warn_saturate+0xe5/0x110
? report_bug+0x171/0x1a0
? refcount_warn_saturate+0xe5/0x110
? handle_bug+0x3c/0x80
? exc_invalid_op+0x17/0x70
? asm_exc_invalid_op+0x1a/0x20
? refcount_warn_saturate+0xe5/0x110
tcp_twsk_unique+0x186/0x190
__inet_check_established+0x176/0x2d0
__inet_hash_connect+0x74/0x7d0
? __pfx___inet_check_established+0x10/0x10
tcp_v4_connect+0x278/0x530
__inet_stream_connect+0x10f/0x3d0
inet_stream_connect+0x3a/0x60
__sys_connect+0xa8/0xd0
__x64_sys_connect+0x18/0x20
do_syscall_64+0x83/0x170
entry_SYSCALL_64_after_hwframe+0x78/0x80
RIP: 0033:0x7f62c11a885d
Code: ff c3 66 2e 0f 1f 84 00 00 00 00 00 90 f3 0f 1e fa 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d a3 45 0c 00 f7 d8 64 89 01 48
RSP: 002b:00007f62c1091e58 EFLAGS: 00000296 ORIG_RAX: 000000000000002a
RAX: ffffffffffffffda RBX: 0000000020ccb004 RCX: 00007f62c11a885d
RDX: 0000000000000010 RSI: 0000000020ccb000 RDI: 0000000000000003
RBP: 00007f62c1091e90 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000296 R12: 00007f62c10926c0
R13: ffffffffffffff88 R14: 0000000000000000 R15: 00007ffe237885b0
</TASK>(CVE-2024-36904)

In the Linux kernel, the following vulnerability has been resolved:

drm/amd/display: Skip on writeback when it's not applicable

[WHY]
dynamic memory safety error detector (KASAN) catches and generates error
messages "BUG: KASAN: slab-out-of-bounds" as writeback connector does not
support certain features which are not initialized.

[HOW]
Skip them when connector type is DRM_MODE_CONNECTOR_WRITEBACK.(CVE-2024-36914)

In the Linux kernel, the following vulnerability has been resolved:

nsh: Restore skb->{protocol,data,mac_header} for outer header in nsh_gso_segment().

syzbot triggered various splats (see [0] and links) by a crafted GSO
packet of VIRTIO_NET_HDR_GSO_UDP layering the following protocols:

ETH_P_8021AD + ETH_P_NSH + ETH_P_IPV6 + IPPROTO_UDP

NSH can encapsulate IPv4, IPv6, Ethernet, NSH, and MPLS. As the inner
protocol can be Ethernet, NSH GSO handler, nsh_gso_segment(), calls
skb_mac_gso_segment() to invoke inner protocol GSO handlers.

nsh_gso_segment() does the following for the original skb before
calling skb_mac_gso_segment()

1. reset skb->network_header
2. save the original skb->{mac_heaeder,mac_len} in a local variable
3. pull the NSH header
4. resets skb->mac_header
5. set up skb->mac_len and skb->protocol for the inner protocol.

and does the following for the segmented skb

6. set ntohs(ETH_P_NSH) to skb->protocol
7. push the NSH header
8. restore skb->mac_header
9. set skb->mac_header + mac_len to skb->network_header
10. restore skb->mac_len

There are two problems in 6-7 and 8-9.

(a)
After 6 & 7, skb->data points to the NSH header, so the outer header
(ETH_P_8021AD in this case) is stripped when skb is sent out of netdev.

Also, if NSH is encapsulated by NSH + Ethernet (so NSH-Ethernet-NSH),
skb_pull() in the first nsh_gso_segment() will make skb->data point
to the middle of the outer NSH or Ethernet header because the Ethernet
header is not pulled by the second nsh_gso_segment().

(b)
While restoring skb->{mac_header,network_header} in 8 & 9,
nsh_gso_segment() does not assume that the data in the linear
buffer is shifted.

However, udp6_ufo_fragment() could shift the data and change
skb->mac_header accordingly as demonstrated by syzbot.

If this happens, even the restored skb->mac_header points to
the middle of the outer header.

It seems nsh_gso_segment() has never worked with outer headers so far.

At the end of nsh_gso_segment(), the outer header must be restored for
the segmented skb, instead of the NSH header.

To do that, let's calculate the outer header position relatively from
the inner header and set skb->{data,mac_header,protocol} properly.

[0]:
BUG: KMSAN: uninit-value in ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline]
BUG: KMSAN: uninit-value in ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
BUG: KMSAN: uninit-value in ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668
ipvlan_process_outbound drivers/net/ipvlan/ipvlan_core.c:524 [inline]
ipvlan_xmit_mode_l3 drivers/net/ipvlan/ipvlan_core.c:602 [inline]
ipvlan_queue_xmit+0xf44/0x16b0 drivers/net/ipvlan/ipvlan_core.c:668
ipvlan_start_xmit+0x5c/0x1a0 drivers/net/ipvlan/ipvlan_main.c:222
__netdev_start_xmit include/linux/netdevice.h:4989 [inline]
netdev_start_xmit include/linux/netdevice.h:5003 [inline]
xmit_one net/core/dev.c:3547 [inline]
dev_hard_start_xmit+0x244/0xa10 net/core/dev.c:3563
__dev_queue_xmit+0x33ed/0x51c0 net/core/dev.c:4351
dev_queue_xmit include/linux/netdevice.h:3171 [inline]
packet_xmit+0x9c/0x6b0 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x8aef/0x9f10 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg net/socket.c:745 [inline]
__sys_sendto+0x735/0xa10 net/socket.c:2191
__do_sys_sendto net/socket.c:2203 [inline]
__se_sys_sendto net/socket.c:2199 [inline]
__x64_sys_sendto+0x125/0x1c0 net/socket.c:2199
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xcf/0x1e0 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b

Uninit was created at:
slab_post_alloc_hook mm/slub.c:3819 [inline]
slab_alloc_node mm/slub.c:3860 [inline]
__do_kmalloc_node mm/slub.c:3980 [inline]
__kmalloc_node_track_caller+0x705/0x1000 mm/slub.c:4001
kmalloc_reserve+0x249/0x4a0 net/core/skbuff.c:582
__
---truncated---(CVE-2024-36933)

In the Linux kernel, the following vulnerability has been resolved:

wifi: ar5523: enable proper endpoint verification

Syzkaller reports [1] hitting a warning about an endpoint in use
not having an expected type to it.

Fix the issue by checking for the existence of all proper
endpoints with their according types intact.

Sadly, this patch has not been tested on real hardware.

[1] Syzkaller report:
------------[ cut here ]------------
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 0 PID: 3643 at drivers/usb/core/urb.c:504 usb_submit_urb+0xed6/0x1880 drivers/usb/core/urb.c:504
...
Call Trace:
<TASK>
ar5523_cmd+0x41b/0x780 drivers/net/wireless/ath/ar5523/ar5523.c:275
ar5523_cmd_read drivers/net/wireless/ath/ar5523/ar5523.c:302 [inline]
ar5523_host_available drivers/net/wireless/ath/ar5523/ar5523.c:1376 [inline]
ar5523_probe+0x14b0/0x1d10 drivers/net/wireless/ath/ar5523/ar5523.c:1655
usb_probe_interface+0x30f/0x7f0 drivers/usb/core/driver.c:396
call_driver_probe drivers/base/dd.c:560 [inline]
really_probe+0x249/0xb90 drivers/base/dd.c:639
__driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808
__device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427
__device_attach+0x1e4/0x530 drivers/base/dd.c:1008
bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487
device_add+0xbd9/0x1e90 drivers/base/core.c:3517
usb_set_configuration+0x101d/0x1900 drivers/usb/core/message.c:2170
usb_generic_driver_probe+0xbe/0x100 drivers/usb/core/generic.c:238
usb_probe_device+0xd8/0x2c0 drivers/usb/core/driver.c:293
call_driver_probe drivers/base/dd.c:560 [inline]
really_probe+0x249/0xb90 drivers/base/dd.c:639
__driver_probe_device+0x1df/0x4d0 drivers/base/dd.c:778
driver_probe_device+0x4c/0x1a0 drivers/base/dd.c:808
__device_attach_driver+0x1d4/0x2e0 drivers/base/dd.c:936
bus_for_each_drv+0x163/0x1e0 drivers/base/bus.c:427
__device_attach+0x1e4/0x530 drivers/base/dd.c:1008
bus_probe_device+0x1e8/0x2a0 drivers/base/bus.c:487
device_add+0xbd9/0x1e90 drivers/base/core.c:3517
usb_new_device.cold+0x685/0x10ad drivers/usb/core/hub.c:2573
hub_port_connect drivers/usb/core/hub.c:5353 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5497 [inline]
port_event drivers/usb/core/hub.c:5653 [inline]
hub_event+0x26cb/0x45d0 drivers/usb/core/hub.c:5735
process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289
worker_thread+0x669/0x1090 kernel/workqueue.c:2436
kthread+0x2e8/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
</TASK>(CVE-2024-38565)

In the Linux kernel, the following vulnerability has been resolved:

eth: sungem: remove .ndo_poll_controller to avoid deadlocks

Erhard reports netpoll warnings from sungem:

netpoll_send_skb_on_dev(): eth0 enabled interrupts in poll (gem_start_xmit+0x0/0x398)
WARNING: CPU: 1 PID: 1 at net/core/netpoll.c:370 netpoll_send_skb+0x1fc/0x20c

gem_poll_controller() disables interrupts, which may sleep.
We can't sleep in netpoll, it has interrupts disabled completely.
Strangely, gem_poll_controller() doesn't even poll the completions,
and instead acts as if an interrupt has fired so it just schedules
NAPI and exits. None of this has been necessary for years, since
netpoll invokes NAPI directly.(CVE-2024-38597)

In the Linux kernel, the following vulnerability has been resolved:

ext4: fix mb_cache_entry's e_refcnt leak in ext4_xattr_block_cache_find()

Syzbot reports a warning as follows:

============================================
WARNING: CPU: 0 PID: 5075 at fs/mbcache.c:419 mb_cache_destroy+0x224/0x290
Modules linked in:
CPU: 0 PID: 5075 Comm: syz-executor199 Not tainted 6.9.0-rc6-gb947cc5bf6d7
RIP: 0010:mb_cache_destroy+0x224/0x290 fs/mbcache.c:419
Call Trace:
<TASK>
ext4_put_super+0x6d4/0xcd0 fs/ext4/super.c:1375
generic_shutdown_super+0x136/0x2d0 fs/super.c:641
kill_block_super+0x44/0x90 fs/super.c:1675
ext4_kill_sb+0x68/0xa0 fs/ext4/super.c:7327
[...]
============================================

This is because when finding an entry in ext4_xattr_block_cache_find(), if
ext4_sb_bread() returns -ENOMEM, the ce's e_refcnt, which has already grown
in the __entry_find(), won't be put away, and eventually trigger the above
issue in mb_cache_destroy() due to reference count leakage.

So call mb_cache_entry_put() on the -ENOMEM error branch as a quick fix.(CVE-2024-39276)

In the Linux kernel, the following vulnerability has been resolved:

netfilter: nf_tables: fully validate NFT_DATA_VALUE on store to data registers

register store validation for NFT_DATA_VALUE is conditional, however,
the datatype is always either NFT_DATA_VALUE or NFT_DATA_VERDICT. This
only requires a new helper function to infer the register type from the
set datatype so this conditional check can be removed. Otherwise,
pointer to chain object can be leaked through the registers.(CVE-2024-42070)

In the Linux kernel, the following vulnerability has been resolved:

crypto: aead,cipher - zeroize key buffer after use

I.G 9.7.B for FIPS 140-3 specifies that variables temporarily holding
cryptographic information should be zeroized once they are no longer
needed. Accomplish this by using kfree_sensitive for buffers that
previously held the private key.(CVE-2024-42229)

In the Linux kernel, the following vulnerability has been resolved:

libceph: fix race between delayed_work() and ceph_monc_stop()

The way the delayed work is handled in ceph_monc_stop() is prone to
races with mon_fault() and possibly also finish_hunting(). Both of
these can requeue the delayed work which wouldn't be canceled by any of
the following code in case that happens after cancel_delayed_work_sync()
runs -- __close_session() doesn't mess with the delayed work in order
to avoid interfering with the hunting interval logic. This part was
missed in commit b5d91704f53e ("libceph: behave in mon_fault() if
cur_mon < 0") and use-after-free can still ensue on monc and objects
that hang off of it, with monc->auth and monc->monmap being
particularly susceptible to quickly being reused.

To fix this:

- clear monc->cur_mon and monc->hunting as part of closing the session
in ceph_monc_stop()
- bail from delayed_work() if monc->cur_mon is cleared, similar to how
it's done in mon_fault() and finish_hunting() (based on monc->hunting)
- call cancel_delayed_work_sync() after the session is closed(CVE-2024-42232)

In the Linux kernel, the following vulnerability has been resolved:

usb: gadget: configfs: Prevent OOB read/write in usb_string_copy()

Userspace provided string 's' could trivially have the length zero. Left
unchecked this will firstly result in an OOB read in the form
`if (str[0 - 1] == '') followed closely by an OOB write in the form
`str[0 - 1] = '\0'`.

There is already a validating check to catch strings that are too long.
Let's supply an additional check for invalid strings that are too short.(CVE-2024-42236)

In the Linux kernel, the following vulnerability has been resolved:

ext4: make sure the first directory block is not a hole

The syzbot constructs a directory that has no dirblock but is non-inline,
i.e. the first directory block is a hole. And no errors are reported when
creating files in this directory in the following flow.

ext4_mknod
...
ext4_add_entry
// Read block 0
ext4_read_dirblock(dir, block, DIRENT)
bh = ext4_bread(NULL, inode, block, 0)
if (!bh && (type == INDEX || type == DIRENT_HTREE))
// The first directory block is a hole
// But type == DIRENT, so no error is reported.

After that, we get a directory block without '.' and '..' but with a valid
dentry. This may cause some code that relies on dot or dotdot (such as
make_indexed_dir()) to crash.

Therefore when ext4_read_dirblock() finds that the first directory block
is a hole report that the filesystem is corrupted and return an error to
avoid loading corrupted data from disk causing something bad.(CVE-2024-42304)

In the Linux kernel, the following vulnerability has been resolved:

drm/gma500: fix null pointer dereference in cdv_intel_lvds_get_modes

In cdv_intel_lvds_get_modes(), the return value of drm_mode_duplicate()
is assigned to mode, which will lead to a NULL pointer dereference on
failure of drm_mode_duplicate(). Add a check to avoid npd.(CVE-2024-42310)

In the Linux kernel, the following vulnerability has been resolved:

bna: adjust 'name' buf size of bna_tcb and bna_ccb structures

To have enough space to write all possible sprintf() args. Currently
'name' size is 16, but the first '%s' specifier may already need at
least 16 characters, since 'bnad->netdev->name' is used there.

For '%d' specifiers, assume that they require:
* 1 char for 'tx_id + tx_info->tcb[i]->id' sum, BNAD_MAX_TXQ_PER_TX is 8
* 2 chars for 'rx_id + rx_info->rx_ctrl[i].ccb->id', BNAD_MAX_RXP_PER_RX
is 16

And replace sprintf with snprintf.

Detected using the static analysis tool - Svace.(CVE-2024-43839)

2. 影响范围

3. 影响组件

4. 修复版本

5. 修复方法

方法一：下载安装包进行升级安装
1、通过下载链接下载需要升级的升级包保存，如 xxx.rpm
2、通过rpm命令升级，如 rpm -Uvh xxx.rpm

方法二：通过软件源进行升级安装
1、保持能够连接上互联网
2、通过yum命令升级指定的包，如 yum install 包名

6. 下载链接

KY3.4-5A:

x86_64:

     kernel   

     python2-perf   

     python3-perf   

     bpftool   

     kernel-source   

     perf   

     kernel-tools-devel   

     kernel-tools   

     kernel-devel   

aarch64:

     bpftool   

     kernel-source   

     kernel   

     kernel-devel   

     kernel-tools   

     kernel-tools-devel   

     perf   

     python2-perf   

     python3-perf